dpdk发送9000字节的包的代码-DPDK中文网

好的，以下是使用DPDK发送9000字节包的示例代码：

#include <stdio.h>
#include <stdlib.h>
#include <string.h>

#include <rte_eal.h>
#include <rte_mbuf.h>
#include <rte_ethdev.h>

#define RX_RING_SIZE 1024
#define TX_RING_SIZE 1024

#define NUM_MBUFS 8191
#define MBUF_CACHE_SIZE 250

static const struct rte_eth_conf port_conf_default = {
    .rxmode = { .max_rx_pkt_len = ETHER_MAX_LEN }
};

int main(int argc, char *argv[])
{
    int ret;
    uint16_t nb_ports;
    uint16_t portid;
    struct rte_mempool *mbuf_pool;
    struct rte_eth_dev_info dev_info;

    /* 初始化 EAL */
    ret = rte_eal_init(argc, argv);
    if (ret < 0)
        rte_exit(EXIT_FAILURE, "Error with EAL initialization\n");

    argc -= ret;
    argv += ret;

    /* 获取网口数量 */
    nb_ports = rte_eth_dev_count_avail();

   /* 创建内存池 */
   mbuf_pool = rte_pktmbuf_pool_create("MBUF_POOL", NUM_MBUFS,
       MBUF_CACHE_SIZE, 0, RTE_MBUF_DEFAULT_BUF_SIZE, rte_socket_id());
    
   /* 配置端口并启动 */
   for (portid = 0; portid < nb_ports; portid++) {
        if (!rte_eth_dev_is_valid_port(portid))
            continue;

        /* 获取网卡信息 */
        memset(&dev_info, 0, sizeof(dev_info));
        rte_eth_dev_info_get(portid, &dev_info);

        /* 配置网卡 */
        ret = rte_eth_dev_configure(portid, 1, 1, &port_conf_default);
        if (ret < 0)
            rte_exit(EXIT_FAILURE, "Cannot configure device: err=%d, port=%u\n",
                ret, portid);

       /* 启动设备 */
       ret = rte_eth_dev_start(portid);
       if (ret < 0)
           rte_exit(EXIT_FAILURE,
               "rte_eth_dev_start:err=%d,port=%u\n",
               ret,(unsigned)portid);

       printf("Ethernet device %u successfully configured.\n", portid);
    }

    /* 创建一个 MBUF 包 */
    struct rte_mbuf *pkt = rte_pktmbuf_alloc(mbuf_pool); // 从内存池中获取一个 MBUF 包
    if (pkt == NULL)
        rte_exit(EXIT_FAILURE, "Cannot allocate mbuf\n");

    /* 设置包头 */
    pkt->data_len = 9000; // 数据长度为9000字节，即一个巨型帧的大小
    pkt->pkt_len = 9000;

    /* 发送 MBUF 包 */
    uint64_t tx_time = 0;
    int nb_tx = rte_eth_tx_burst(0, 0, &pkt, 1);
    if (nb_tx == 1) {
        /* 等待数据发送完毕 */
        do {
            nb_tx = rte_eth_tx_done_cleanup(0, BURST_SIZE);
            tx_time += rte_get_timer_cycles();
            rte_delay_us(5);
        } while (nb_tx);

       printf("TX time: %lu cycles\n", tx_time); 
   } else {
       rte_pktmbuf_free(pkt); // 如果发送失败则释放 MBUF 包
   }

   return 0;
}

以上代码创建了一个内存池和一个网口，并使用DPDK发送了一个9000字节的巨型帧。需要注意的是，实际应用中可能需要更加复杂的逻辑来处理巨型帧。